|
Starting at Only $89.99
Comes with a 10 Year Guarantee! (click for details)
 |
70 CFM Ventilation Fan & Incandescent Light
Model No. CBFV70LMG - 120 WATT MAX
Bathrooms, Bedrooms, Family Room, Kitchen! |
• Galvanized housing for humid conditions and various attic temperatures
• Built-in mounting tabs for quick installation
• Markings on housing for ceiling / wall thickness
• Built-in junction box for easy wiring
• Molded 4" duct adapter with built-in damper
• Built-in receptacles for quick activation
• Easy to remove and install motor assembly-key hole mounting bracket included |
• Permanently lubricated motor with plug for quick activation
• Molded impeller and propeller-precision balanced for quiet operation
• Only 3.5 Sones
• Low profile, yet decorative!
• Frosted Glass Globe
• Precision stamped grille with 360 degree air openings
• Twin 60 Watt Incandescent lamp holder (bulb not included) |
Available in White Powdercoat, Electro-Plated Polished Brass,
Brushed Stainless Steel, or Physical Vapor Deposition Polished Brass |
DIMENSIONS
Housing: 7 3/4" x 6 3/4" x 5 3/4"
Grille: 13" Diameter x 6" Deep |
|
|
Also Available in Energy-Saving Fluorescent! (click for details)
 |
Starting at $89.99
DISCONTINUED
|
| Due to the low profit margin on this item we do not accept returns unless damaged or defective. Please refer to our terms of sale for complete details. |
INSTALLATION NOTES:
1) Attach duct adapter to housing, Align locking tabs on adapter with holes on housing, Snap into place.
2) Attach housing to joist with screws or nails. Housing is stamped to show 3/4" Standard Sheetrock / Plaster and 3/8" Drywall, Adjust Accordingly.
3) Wire with 120VAC - 60Hz power leads, use the appropriate knock-out location on the housing and with an appropriate wire connector (BX or Romex)
4) Remove outlet box cover by removing screw and pulling downward.
5) TURN OFF ELECTRICAL POWER AT SERVICE ENTRANCE!
6) Connect wire from wall switch to motor wires, and connect all remaining wires for light. Use approved wire connectors - white to white, black to black, and green to ground.
7) Replace outlet box cover and screw.
8) Install 4" duct to duct adapter and run to a roof jack or wall cap to ensure ventilation is ducted to the outside.
9) Install cover to housing with spring clips and or screw provided.
CAUTION: Be sure all wiring complies with local and national electric codes, and housing is properly grounded.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
2) Before servicing or cleaning this unit, switch power OFF at service panel and lock service panel to prevent power from being switched on accidentally. If the service panel cannot be locked, fasten a prominent warning device to the service panel (such as a tag).
3) Installation and all electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
4) Do NOT use this fan with any solid-state speed control device.
5) When cutting or drilling into a wall or ceiling, do NOT damage electrical wiring or other hidden utilities.
6) Ducted fans MUST ALWAYS be vented to outdoors.
7) Never install or place a switch where it can be reached from a tub or shower.
8) NOT for use in kitchens
9) NOT for use with heating equipment, fuel burning equipment or chimneys.
10) This unit MUST be grounded.
11) Keep drywall spray and construction dirt off motor assembly to avoid bearing damage and/or unbalanced impellars. |
| 
|
